1.軋制過程中，冷床作業人員嚴禁上冷床，不準在輥道、齒條上行走。

2.生產中出現亂床等事故，必須等停軋以后進行處理清出。

3.冷床取樣要使用專用工具進行取樣。

4.作業中應注意觀察周圍的情況，無關人員嚴禁進入大冷床的危險區域。

5.因亂床等事故造成的熱廢品，當班必須清出，確保冷床周圍的環境整潔。

1. in the process of rolling, cooling bed workers strictly on bed, don't walk on the roller rack.

2. in the production of random beds, such as accidents, must wait after the stop rolling process to clear out.

3. bed to use a special tool for sampling sampling.

Should observe the situation around 4. operati, unrelated pers non dangerous region in the cold bed.

Waste heat 5. bed because of chaos caused by the accident, the duty must be clear, to ensure the surrounding environment clean bed。

保證合理有序的過鋼節奏，加大矯直測量次數，確保矯直中心在一條直線上。制定矯直輥裝配標準，保證安裝正確，有據可查。建立BH值與矯直輥間距的關系，做到合理配輥，保證輥縫在1－3mm之間。

Ensure a reasonable and orderly flow of steel rhythm, increase the number of straightening measurement, to ensure that the straightening center in a straight line. The assembly standard of straightening roller is set up to ensure that the installation is correct and can be checked up. The relatihip between the BH value and the spacing of the straightening roller is established, and a reasonable roll matching is made to ensure the gap between 1 and 3mm.

工藝過程是：線材出精軋機后先入水冷導管進行急冷，冷卻到650～750℃，經成圈器成圈后落入流態床中。其他優點是冷卻溫度比較均勻，溫差不大于5～10℃，而且不具有粘著性，不會像鉛浴或鹽浴處理時出現掛鉛、掛鹽現象。流態床用流動的、導熱性好的粒料(鋯砂，含ZrO267.2%；SiO232.8%)作媒介，用鼓風機攪動這些顆粒呈懸浮運動狀態，如同鉛浴池中的鉛液沸騰一樣。

The process is as follows: after the wire is finished, the first step is to enter the water cooling pipe and then to cool it to 650~750 degrees. The flow bed is used as a medium for flowing, good thermal conductivity particles (zirconium sand, containing ZrO267.2%; SiO232.8%). The particles are stirred by the blower to move in suspension, just as the lead liquid in the lead bath is boiling.