冷、熱坯（600℃）生產時，合格的連鑄坯以單根方式從連鑄坯出坯臺架送入熱送輥道，坯料在運送過程中由自動測長裝臵對坯料進行測長（使坯料進入加熱爐后能準確對中）.

The cold and hot billet (600 DEG C) production, continuous casting billet qualified with single way from continuous casting billet bench into the hot delivery roller, blank in the process of delivery by the automatic measuring device of billet length (the blank in the heating furnace can accurately on).

整個軋鋼生產過程總是有以下幾個基本工序組成的：

坯料準備，包括表面缺陷的清理，表面氧化鐵皮的去除和坯料的預先熱處理等。坯料的加熱，是熱軋生產工藝過程的重要工序。

The whole rolling process of steel rolling is always composed of the following basic processes:

Preparation of the billet, including the cleaning of surface defects, the removal of the iron oxide skin on the surface, and the pre heat treatment of the blank. The heating of the billet is an important process in the process of hot rolling.

同時在了解技術要求的同時，我們還必須充分了解各種鋼的內在特性，尤其是加工工藝特性及組織性能的變化特性，即該鋼種的固有內在規律，然后利用這些規律，我們才能真確的制訂生產工藝過程及采取有效地工藝手段，來達到生產出合乎技術要求的產品目標。

At the same time to understand the technical requirements at the same time, we must also fully understand the inherent characteristics of all kinds of steel, especially the characteristics of manufacturing process characteristics and organizational performance, namely the inherent inherent law of the steel, and then use these rules, make production process and take effective technical means we  true, to produce a the technical requirements of the product target.

切分刀粘鋼是如何引起的？軋鋼原料：目前主要為連鑄坯，另外還有鋼錠，段軋鋼等，正確的選擇坯料的種類，斷面形狀和尺寸大小以及重量對軋鋼生產具有重要意義。（1）切分孔型老化，切分孔出來的料在切分契尖處較厚，增加了切分刀的切分負荷；（2）切分道和孔型不對中，使切分刀不能順利切開料型，引起粘鋼；（3）切分處冷卻水冷卻效果不好，導致粘鋼；（4）料型控制不好，或有條頭和開花頭現象，使切分刀不能順利切開料型。

How does the slitting tool stick to the steel?

(1) the slitting hole is aging. The cutting hole is thicker at the cut point and the cutting load is thicker. (2) the cutting section and the pass are not in the middle, so that the cutting tool can not cut the material well and cause the sticky steel. (3) the cooling effect of the cooling water is not good, and (4) the  of the material type is not good, or there is a strip head and the flower head phenomenon, so that the cutting knife can't go smoothly. Cut the material type.