1.軋制過程中，冷床作業人員嚴禁上冷床，不準在輥道、齒條上行走。

2.生產中出現亂床等事故，必須等停軋以后進行處理清出。

3.冷床取樣要使用專用工具進行取樣。

4.作業中應注意觀察周圍的情況，無關人員嚴禁進入大冷床的危險區域。

5.因亂床等事故造成的熱廢品，當班必須清出，確保冷床周圍的環境整潔。

1. in the process of rolling, cooling bed workers strictly on bed, don't walk on the roller rack.

2. in the production of random beds, such as accidents, must wait after the stop rolling process to clear out.

3. bed to use a special tool for sampling sampling.

Should observe the situation around 4. operati, unrelated pers non dangerous region in the cold bed.

Waste heat 5. bed because of chaos caused by the accident, the duty must be clear, to ensure the surrounding environment clean bed。

明確軸向位置，加大矯直壓力。不要單獨打8輥軸向，調整側彎時應以每相臨的3個輥為一個調整單元，保證矯直穩定性。為適應不同型號、不同厚度的角鋼，防傾翻裝置的上有一個可以隨時取放配重的斗殼，這樣就可以實現不同型號、不同厚度角鋼在裙板處穩定下滑。側壁斜度的處理措施是經常注意檢查各輥軸向位置，竄動情況。注意在不同間隙情況下，矯直力的選取。對H2與H3的測量做到每批抽查，以做到及時調整。

The axial  is clearly defined and the straightening pressure is increased. Do not play the 8 roll axis alone. When adjusting the side bend, 3 rolls per phase should be used as an adjustment unit to ensure the straightening stability. The treatment of side wall slope is to check the axial  and movement of each roll. Pay attention to the selection of maximum straightening force under different clearance conditi. The measurement of H2 and H3 is done in each batch, so as to adjust it in time.

矯直板位于冷床入口側, 由制動裙板拔入的軋制棒材首先落到矯直板上, 使棒材保持大平直度。矯直板每塊長1. 15m, 寬250mm , 上有10個齒形, 塊與塊之間只留出動齒條移動間隙, 安裝在定支架上。

The straightening plate is located on the inlet side of the cooling bed, and the rolled bar pulled by the brake apron first falls on the straightening plate to maintain the maximum flatness of the bar. The straightening plate is 1. 15m long and 10 250mm wide. There is only a movable clearance between the block and block, which is installed on the fixed support.