混流泵

（二）泵蓋是泵與進水管相連的零件，其端面與葉輪之間留有規定的軸向端面間隙（在消除軸承軸向活動間隙以后，保持規定的軸向間隙）。間隙過小產生磨擦，過大則會導致泵內壓力水回流，使泵的效率降低，通過增減調整紙墊達到規定的間隙。

II.  Pump cover is

the part connected with water inlet pipe.There is an stated axial end face gap

between its end

face and

impeller(Keep the stated axail gap after removing the bearing axial movable

gap).Friction will be

produced if

the gap is too small, contrary, if the gap is too large, the pressure water in

pump will reflux which

makes the

feeiciency reduced.Adjust the paper washer and make the gap be stated one.

 8、填料處漏水太多

 The padding is

 leaking water too much

 1、填料壓得太松

 2、填料裝置不好

 3、填料大小不一或磨損過多

 4、填料質量差，密封性不好

 5、軸套磨損太多

 1.The padding is pressed too loose

 2.The padding does not assemble well

 3.The padding is not of niform size or it

 wears too much

 4.The padding is with bad quality and

 tightness

 5.

 1、上緊壓蓋到適應程度

 2、調整填料搭口，使之錯開一定角度而不在一個方向

 3、更換填料

 4、更換符合要求的石棉填料

 5、更換軸套

 1.Tighten the gland up to suitable degree

 2.Adjust the padding jiont up to some

 angle not in the same direction.

 3.Change the padding

 4.Change the suitable asbestos padding

 5.Change the axle sleeve.

按介質分類清水泵、污水泵、海水泵、熱水泵、熱油泵、稠油泵、機油泵、重油泵、渣油泵、瀝青泵、雜質泵、渣漿泵、沙漿泵、灰漿泵、灰渣泵、泥漿泵、水泥泵、混凝土泵、粉末泵、酸堿泵、空氣泵、蒸汽泵、氧氣泵、氨氣泵、煤氣泵、血液泵、泡沫泵、乳液泵、涂料泵、硫酸泵、鹽酸泵、膠體泵、酒精泵、啤酒泵、葡萄酒泵、巧克力泵、奶泵、淀粉泵、麥汁泵、牙膏泵、鹽鹵泵、鹵水泵、堿液泵、熔鹽泵、油脂泵、 、化肥泵、藥劑泵、氣液泵、油劑泵、化纖泵、紡絲泵、劑量泵、油漆泵、果漿泵、紙漿泵、胰島素泵、濃漿泵、氣泵、水泵、油泵