目前，法蘭連接中大的問題主要是法蘭本身不合格和法蘭連接不合格。

現在市場上銷售的一些法蘭存在的質量問題有：

①法蘭的鋼材不合格，PVC管業加盟，耐壓強度較低，PVC管業生產，在使用若干個月或若干個年后，出現滲水。

②法蘭的螺栓孔外緣距法蘭的邊緣太小，小于5mm，在螺栓緊固時，易使法蘭邊緣。

At present， the major problems in flange connection are the unqualified flange itself and the flange connection is unqualified.

Some of the quality problems of the flange sold in the market are as follows:

① The flange steel is unqualified and the pressure resistance is low. After several months or years of use， water seepage occurs.

② The outer edge of bolt hole of flange is too small from the flange edge， less than 5mm. When the bolts are tightened， it is easy to make the flange edge.

在熔管的時候，先用PPR管剪刀切好ppr管。切割時要把管子斷面盡量剪平，沒有毛邊和毛刺，管材和管件連接端面必須清潔，干燥、無污染，否則會影響熔接效果。并在管材熔接口標上熔接深度線。

When melting the pipe，PVC管業加工， first cut the PPR pipe with PPR pipe scissors. When cutting， the cross-section of the pipe Try to cut it flat without burr and burr. The connecting end face of the pipe and fittings must be clean，麗水PVC管業， dry and pollution-free， otherwise the welding effect will be affected. And the welding depth line is marked on the pipe welding joint.

ppr管在電氣部分：

衛生間的開關盡量放在室外，若放在室內有淋浴的需加裝防濺盒，使用不方便還會增加成本。

衛生間等電位聯結線好利用近的柱筋引入（若有均壓環更好）。

PPR tube in the electrical part:

The switch of toilet should be put outdoors to the full. If it is put indoors with shower， splash proof box should be added， which will increase the cost if it is inconvenient to use.

The equipotential bonding line in the toilet should be introduced by using the bar near the column (if there is a grading ring， it is better).

PVC管業加盟-麗水PVC管業-Gafloon卡弗龍(查看)由臺州艾菲力塑膠有限公司提供。臺州艾菲力塑膠有限公司實力不俗，信譽可靠，在浙江 臺州 的塑料管等行業積累了大批忠誠的客戶。艾菲力塑膠帶著精益求精的工作態度和不斷的完善創新理念和您攜手步入輝煌，共創美好未來！同時本公司還是從事PPR管，地暖管，PVC管的廠家，歡迎來電咨詢。